Circular based chair has rectangular back and curved armrest with same decorative intertwined bamboo splints. Bamboo splints interwoven in plait-like weave on seat, surrounded by bamboo grass tied with bark. Support of 2 inverted v shaped branches, one part of branch in base the other extends behind chair; all joints affixed with black glue. Criss-crossing bark under seat, and wrapping around rim underneath gathered bamboo grass. Base: wide smooth overlapping wood strip forms circular base; crisscrossing bamboo strips extend upward from base to wooden rim at bottom of chair seat. Black adhesive is used on all joints.

A loom with an incomplete textile; the shedding device is a number of narrow sticks with one hole in the centre of each which are lashed together leaving narrow spaces. This is lashed to a longer round stick. The unwoven warps are threaded through the holes and the spaces between sticks. 241 cm of unwoven warp twist together on one side of the shedding device. On the other side is 33 cm of unwoven warp and 304 cm of woven band with fringe like loops extending from one side. The band is speckled grey and the fringes alternate areas of grey with short areas of red, blue, white and green. At the junction of the woven band and unwoven warp, two weft of cross threads are attached to the textile. One is a small grey finger skein and the other is also grey but is wound on the shaft of a wooden spindle with a cone shaped whorl.

Oval face with prominent brows and crease between brows. Round wooden, closely spaced, inlay eyes in corners of deep horizontal groove. Triangular nose, prominent cheeks and mouth, and incised teeth rows at bottom.

Oval face with prominent brows and crease between. Round wooden inlay eyes, closely spaced, in corners of deep horizontal groove. Triangular nose in higher relief than prominent cheeks and mouth. Teeth row incised, above sloping chin. Mottled dentine shows at crown and lower relief.

Spindle, consisting of a wooden shaft with a cone shaped whorl near one end with a conical, wrapped section of plied yarn resting on the flat surface of the whorl. The middle of the shaft has a section of losing wound, plied yarn which is attached to a compactly wound round ball of paired yarns. The yarn wound around the shaft is tightly plied while the yarn in the ball is not plied.

Bee mask. Slightly rounded white forehead has a black and yellow horizontal curvilinear design, red ovoid at centre of yellow; raised thick curved black brows; thin yellow line joins orbital areas at dip between forehead and large protruding bulbous snout; yellow round hollow protruding eyes with black and white bands around pupil; snout has black triangular shape at top and bottom joined by a narrow band, black outline; cluster of five holes, top hole on right has remains of 'stinger'; white, yellow and red crescentic designs around circular white hollow nostrils; white temple; defining line for cheeks melds with orbital ridge; curvilinear black line on cheek; square-like white line defines black split U on either side of mouth area; white and yellow bands around small pointed protruding red lip band, painted design converges at lower lip point; yellow triangle on upturned chin is outlined in white. Cut cedar bark, tied with white cord, folded around a folded orange-pink cloth and nailed to upper rim; white cord and red cloth are twined into the cedar bark lengths; at side on right folded white cloth, stitched with yellow thread, is nailed at temples; brown cord twined into first 7cm. of bark. On reverse, one brown cord passes through two holes in upper rim, looped and knotted through hole at each temple; second cord is looped and knotted through chin.

Bowhead whale shaped toggle with transverse hole drilled at centre. Short u-shaped flippers on sides next to wood ? inlaid eyes. Incised downturned mouth extends from just below each eye across large tapering snout. Narrows considerably to fluked tail at back.

Miniature carved seal with flat snout; black circular graphite eyes on top of slightly rounded head. Body tapers to back. Triangular flippers with triangular notch between. Short flippers at front bottom. Hole drilled through centre top to bottom. Sawn at both ends, rasp-like marks and some scratches on smooth surface. Small amount of mottled dentine at top of head. Entire figure is mounted on a rectangular, brown wooden base.

Miniature, carved arctic fox with tapering snout, incised mouth on flat end with nostrils at top. Eyes on sloping face with erect ears at top of head; straight body with tail out straight behind; contoured legs. Stain on top back, shallow holes on each side and on one back leg. Longitudinal cracks on body; 'Mastodon' printed on side; rectangle tape mark on one side. Entire figure is mounted on a rectangular, brown wooden base.

Wild man or Bukwus mask with three shades of green paint on a skeletal face, with red, white and black used to emphasize facial features. Red horsehair has been stapled to top rim and centre of dome-like forehead; on either side of forehead natural wood horn-like projections have been pegged and glued, projection on left is loose; black brows, outlined in white, graduate in size from bridge of nose to side orbital ridge; curvilinear design from brows to side rim; sunken eye areas with hollow eyes; hooked nose with hollow flaring nostrils; bulbous protrusion on each cheek; wide gaping mouth exposes buck-teeth of natural wood; black and white form line design extends from nostrils around mouth to chin; white line divides cheek and chin from jaw. On reverse, four leather strips pass through holes drilled at sides and top and artist signature. Small sliver of wood lifted from front at side on right; peg for horn-like protrusion on left visible on reverse.